Emerson Custom 4 Knob Prewired Kit for PRS Guitars -Premier Pro

$125.00 USD
By Emerson

Maker: Emerson Custom

Model: 4 Knob Prewired Kit for PRS Guitars - Premier Pro

Condition: New

 

Description:

EMERSON PREMIER PRO POTS

We at Emerson Custom formerly had our own spec’d line of “Emerson PRO CTS pots” but when 2020 rolled around and the supply chain blew up, it was finally time to take matters into our own hands. Faced with lead-times that were 20x longer than that of during a normal time, Mitch was stuck between a rock and a hard place. He didn’t have access to his own supply of his spec of CTS pots because all the major brands were vying for anything and everything they could get from the factories. Mitch was tired of simply accepting the industry norm that CTS pots are “good enough”, or the “best” available. So, he set out to create his very own design and brand of in-house pots that not only look familiar but are built to an incredibly consistent feel and function from lot to lot. It took a ton of money, time and effort, but we feel that these new Emerson PREMIER PRO pots are the best pots available… PERIOD.  We weren’t constrained by an off the shelf spec sheet of options to choose from.

We designed and developed these pots from the ground up. The feel and consistency from pot to pot is incredible. We put extra care into the little details to make sure these translate to the end user. We built these to be rugged and reliable. We chose to use robust Fiberglass as the substrate the solder lugs and resistive track are mounted to because its super strong, rigid, and won’t easily bend and snap like those in most every guitar. The taper we used on these is a custom 20% Audio Taper that is a proprietary design from Emerson. This taper works equally as well in the volume position as it does in the tone position. Our Solder lugs are a unique design… slightly oversized for plenty of room to run ground wires/buss wires and any other connection you need to the pot lugs.

4-KNOB PREWIRED KIT FOR PRS GUITARS
  • Handwired in the USA
  • Wired 50's style for authentic vintage sound and feel.
Description

This is a prewired harness for PRS 4-Knob Guitars. Carefully wired “50’s Style” and grounded with vintage spec buss wire for a great vintage tone. For import guitars you may need to enlarge the holes for the higher quality US spec electronics to fit and also you may need US Spec knobs (to accept 24 teeth split shafts).

Includes 
  • (4) 500K Emerson PREMIER PRO Pots
  • (1) Switchcraft J11 1/4" mono input jack (MADE IN USA) 
  • (2) Emerson Bumblebee Paper in Oil Capacitors (1: 0.022uf Bridge, & 1: 0.015uf Neck) 
  • (1) Wiring Diagram
Additional Information

(Pre-wired 3-Way Toggle Switch available for an even easier install)
Click HERE for more information.

What’s so special about ’50s style wiring? It affects your tone in three major ways:

  1. The overall tone gets stronger, tighter, and more transparent. It’s difficult to describe, but you might say it’s more “in your face.”
  2. The typical treble loss that occurs when rolling back the volume is much less than with standard wiring. Both the volume and tone controls become more responsive, and they react more smoothly without the usual hot spots. Another bonus: By simply rolling back your guitar volume a bit, you can clean up an overdriven amp without getting lost in the mix.
  3. The tone and the volume controls interact with each other—something you might be familiar with from certain tweed-era Fender tube amps. When you change the volume, the tone changes a little bit as well, and vice-versa. This may be strange at first, but you only need a few minutes to get used to it.
Installation Tips for Knobs on Split Shaft Pots

Our Emerson PREMIER PRO split shaft pots are made to fit USA Spec 24 spline push-on knobs. Some USA & Import Guitars will need new USA Spec Knobs as even some US makers use import spec parts which will not work with our pots. We recommend that you don't rush the knob install process. If your knob is too tight and is not going on ,slightly crimp together the top of the potentiometers shaft ever so slightly so that when you go to push on the knob you don't damage the pot shaft by exerting too much downward pressure. If you have any questions regarding install please let us know. Thank you.