$229.00 USD
Maker: Walrus Audio
Model: Slötvå
Condition: New
Description:
The Slötvå Multi Texture Reverb is a variant of the Slö but adds on the ability to create and save three presets. Save your favorite dreamscapes by simultaneously pressing and holding down on the bypass and sustain switches. Scroll through them by simultaneously pressing and releasing bypass and sustain.
The Slötvå allows players to create lush, modulated, sleepy, and ambient soundscapes. Stocked with three different algorithms specifically designed to invoke textures for bringing dreams from your subconscious to reality.
The toggle switch allows three different reverb modes, Dark (Lower Octave), Rise (Ambient Swell), and Dream (Latching Pad), while secondary functions on the switch change between different wave shapes for the modulation on the reverb trail.
Combine deep modulation with long washy trails and experience, the Slötvå.
ALGORITHMS:
DARK – Add a lower octave to your reverb trail. Here you'll create deep and wide atmospheric sounds and channel nightmarish soundscapes. X knob sets the level of a -1 octave signal that feeds the reverb.
RISE – This is an auto-swell reverb for beautiful cinematic swells. Don't rush it. Let it breathe and gently wake up. X knob sets the amount of time it takes the reverb to swell in after a note is played. Set lower for shorter rise times and higher for longer rise times.
DREAM – Lush reverb with a latching pad function. Press the sustain switch to latch signal. Experiment with the X knob to add vibrato over the pad. Press sustain again and the pad will decrescendo according to where the decay knob is set. X knob sets the depth of vibrato applied to the reverb trail.
The Slötvå also features 3 different wave shapes accessible by holding down bypass while switching the algorithm toggle.
SINE – Smooth and even pitch up and down modulation.
WARP – Asymmetric pitch up modulation similar to a warped record.
SINK – Asymmetric pitch down modulation for sinking detune similar to a Bigsby.
MOMENTARY FUNCTIONS:
Bypass: When the switch is in the off position, press and hold to temporarily activate the effect to add a moment of reverb texture. Releasing the switch turns the effect off, and fades it out.
Sustain: When pressed, the decay switch ramps up the reverb trail to maximum creating a long dreamy reverb trail, and then ramps back down to the decay knob setting when released. In the “Dream” algorithm, the sustain switch is latching. Press it once to capture and sustain the current reverb decay for extremely long pad-like sounds. Press it again to let the reverb trail taper off, based on the position of the decay knob.
TRAILS MODE:
The Slötvå can run in trails or no trails mode. In trails mode, when you turn the pedal off, the reverb decay dies off naturally. In no trails mode, the decay is abruptly cut off when you turn the pedal off. To toggle between either mode, hold down the bypass switch for 1 second while applying power to the pedal. Unplug power and repeat to toggle to the other mode.
PRESET SPILLOVER
When scrolling through presets, there is only preset spillover if the next preset is the same algorithm as the one preceding it. For example, if your red and green presets are both in Dream mode, switching from red to green will not cut your reverb trails.
Three On Board Presets:
Save your favorite dreamscapes by simultaneously pressing and holding down on the bypass and sustain switches. Scroll through them by simultaneously pressing and releasing bypass and sustain.
Dark Mode:
Add a lower octave to your reverb trail. Create deep and wide atmospheric sounds and channel nightmarish soundscapes. X knob sets the level of a -1 octave signal that feeds the reverb.
Rise Mode:
Auto-swell reverb for beautiful cinematic swells. Don’t rush it. Let it breathe and gently wake up. X knob sets the amount of time it takes the reverb to swell in after a note is played. Set lower for shorter rise times and higher for longer rise times.
Dream Mode:
Lush reverb with a latching pad function. Press the sustain switch to latch signal. Experiment with the X knob to add vibrato over the pad. Press sustain again and pad will decrescendo according to where decay knob is set. X knob sets the depth of vibrato applied to the reverb trail.
Specs:
$349.00 USD
Maker: Walrus Audio Model: SLÖER Condition: New : The Slöer Stereo Ambient Reverb builds on our popular Slö lineup but adds two additional reverb algorithms, stereo width control, two additional modulation...
$199.00 USD
Maker: Walrus Audio Model: Julia V2 Condition: New : The Julia is a fully analog, feature-rich chorus/vibrato packed with a wide array of tonal landscapes begging to be explored. Updated for...
Sold Out - $199.00 USD
Maker: Walrus Audio Model: Polychrome Condition: New : Like the Iguana that’s malleable to its environment, blending in to its surroundings for harmonious balance or standing out with vibrant confidence, the...
$299.00 USD
Maker: Walrus Audio Model: Melee Condition: New : We give you the two most quintessential effects that yield unruly amounts of power and influence to an instrumentalist: reverb and distortion. They have...